CP Plus Camera and NVR Configuration

CP Plus Camera and NVR Configuration

NVR Configuration


The CP Plus Pro Series of NVRs have been meticulously designed for providing you with upgraded performance and higher recording quality in your IP video surveillance solution. The robust processor that has been inculcated in this NVR lets you enjoy 4K resolution and brings out every little detail from the picture in a clear view. This NVR is being used worldwide at a variety of places because of its easy-to-install design.
  1. Connect the NVR to the switch port.
  2. Change the default IP 192.168.1.250 to  an IPA based on your Network configuration (example 192.168.7.53)
  3. In the NVR GUI interface select NETWORK option and change the default IP address to static and change to preferred IP address.




  1. Select MANAGE option and Select ADD IP CAM and ADD option to add the connected IP Camera’s.



Camera Configuration


All the cameras have been configured directly through web (or) though NVR.
  1. Login into NVR through web GUI with Ip Address.
  2. In the NVR GUI interface right click on the camera and select set the IP address, gateway, DNS address.




  1. If unable to initialize the cameras in the NVR, try logging in to the camera with default IP address 192.168.1.250
    1. Username: admin
    2. Password: There is no default password for the CP Plus camera, click ‘Forgot Password’
  2. Install GcMOB software application and scan the QR in the camera GUI interface.

Alternate Option

  1. Connect the device to the monitor and then connect a mouse.
  2. Click the power button at the front or rear panel and then boot up the device. After device booted up, the system is in multiple-channel display mode by default.
  3. Follow above steps once login the camera with default IP and change it too static.
  4. Set system time zone according to the actual environment.





  1. Scan the QR code and get the security code through mail.
  2. Reset the password.
  3. Change the default static IP and assign the new IP address and gateway.


    • Related Articles

    • How to fix the camera issue in Laptop / Camera not working

      Root cause: Solution 1 Follow the below steps: Go to Settings -> Privacy -> Camera -> Enable - Allow apps to enable camera -> and enable access to required listed apps. check again if the camera is working or not else continue to the below steps. Go ...

    • Plustek A350 Scanner - Configuration Option Missing

      How to restore the Configuration option back on the main menu screen Customers may reportedly complain that a configuration option is missing and take various actions or steps like as restarts, driver updates, setting resets, and so on. But in ...

    • Plustek Passport Scanner X-Mini Configuration and Calibration

      Plustek Passport Scanner X-Mini Configuration and Calibration SecureScan X-Mini is a portable scanner for Passports and ID cards, SecureScan X-Mini can capture and verify relevant data of all international passports, plastic ID cards and other ...

    • How to Partition, Format, and Mount Secondary Drives in Linux - Manual Drive Configuration (MDC)

      Introduction This guide provides detailed instructions on how to manually configure secondary drives in a Linux system, including partitioning, formatting, and mounting the drives. Warning Performing these steps on an existing primary drive or a ...

    • Ruijie Access Point Configuration - Putty

      Ruijie Access Point Configuration - Putty Required components: POE Switch, Console cable, Laptop / Desktop, Ruijie Access Point, Network cable Power in POE switch with power cable and connect AP and Switch using a Network cable. Connect the Console ...

    • Popular Articles

    • CP Plus Camera and NVR Configuration

      NVR Configuration The CP Plus Pro Series of NVRs have been meticulously designed for providing you with upgraded performance and higher recording quality in your IP video surveillance solution. The robust processor that has been inculcated in this ...

    • Kerberos Authentication – Overview

      What is Kerberos? Kerberos is a secure authentication method used in our Active Directory (AD) environment (mbuzztech.com). It allows users to: Access multiple systems without re-entering passwords (Single Sign-On – SSO) Log in once Where We Use It ...

    • How to Remove and Reinstall NVIDIA Drivers on Ubuntu

      This article provides step by step guide to completely remove existing NVIDIA drivers and reinstall specific version of the NVIDIA driver on the Ubuntu system Prerequisites Administrative (sudo) access to the Ubuntu system. Internet access to ...

    • Personal Computers and Servers - Classification and Point of Contact

      We can classify the computers that MBUZZ handles based on their form-factor as below: Tower Workstations, Desktops, Gaming PCs and SFF (Small form factor) PCs fall under this category. These are computers people would use on a desk and rarely move. ...

    • M.2 SSD Tier List

      The sequential read and write speeds, which are usually the most advertised number, are not a proper benchmark of real-world performance or the quality of an SSD. This article categorizes and tiers SSDs based on factors like the type of NAND flash, ...